多模态影像学检查在诊断早期强直性脊柱炎骶髂关节疾病中的效果

目的:探究在早期强直性脊柱炎骶髂关节疾病诊断中不同放射影像学检查方法的应用效果。方法:抽取2018年5月-2020年1月本院收治的早期强直性脊柱炎骶髂关节疾病患者65例作为研究对象,所有患者均开展X线、CT、MRI影像学检查,对比三种不同影像学检查方法的检出率、影像学特征。结果:X线、CT、MRI检出率分别为38.46%(25/65)、60.00%(39/65)、76.92%(50/65),检出率相比,MRI、CT明显高于X线,P<0.05;X线、CT、MRI影像学特征,发现关节间隙出现不同的异常,如关节面出现侵蚀、骨质囊变现象,关节面下骨质出现硬化与关节软骨出现肿胀,其中MRI、CT检查,阳性率高于X线,P<0.05。而对于软组织肿胀、骨髓水肿、滑膜炎症、关节滑膜增厚等现象,只能通过MRI检查才能诊断。结论:在早期强直性脊柱炎骶髂关节疾病诊断中,X线、CT、MRI影像学检查均具有一定的指导意义,而MRI不仅可以提高检出率,还能准确反映微小病灶及其软组织病变,对于早期发现骶髂关节炎值得推荐。     

采用温控和碘吸收池技术的发射激光稳频技术

多普勒测风激光雷达通过分析系统回波信号的多普勒频移反演出风速，为提高风场探测精度，从稳频技术方面展开研究。在稳频过程中，分别采取措施消除激光频率的长期漂移和短期抖动。针对激光频率的长期漂移，设计并研制了种子激光器温控箱，通过水浴的控温方式大大减小了激光频率的长期漂移，将激光频率稳定在±50 MHz以内；针对激光频率的短期抖动，采用以碘分子吸收池为核心器件的稳频系统，通过半导体控温方式对碘分子吸收池精确控温，控温精度达0.03 ℃，提高了稳频精度，将激光频率进一步稳定在±8 MHz以内，满足±10 MHz以内的设计精度要求。通过搭建多普勒测风激光雷达系统，对发射激光稳频装置进行系统验证，连续4组风场观测结果表明:系统探测高度为17 km，绝大部分方差在4 m/s以下，满足测风激光雷达测量指标的要求。     

Inconel 690传热管GTAW对接焊接头组织及力学性能研究

对Inconel 690传热管材进行钨极气体保护焊(GTAW)对接焊,采用拉伸试验机、压扁试验机和光学显微镜测试和分析传热管焊接接头,同时利用ANSYS软件开展焊接接头在设计工况失压时的一次应力强度校核。研究结果表明:焊缝中心为树枝胞状晶,熔合线附近为粗大柱状晶。室温时接头的平均抗拉强度为619 MPa,平均屈服强度为292 MPa,350℃时接头平均抗拉强度为475 MPa,平均屈服强度为206 MPa,拉伸接头断裂从熔合区开始贯穿整个焊缝组织,呈塑性断裂。压扁试验和反向压扁试验结果表明管接头完好。通过ANSYS分析可知,设计工况下传热管接头350℃许用应力强度150 MPa限值可满足其一次应力强度要求,且裕量较大。     

Speciation of copper in high chloride concentrations,in the context of corrosion of copper canisters

Canisters with a cast iron insert for mechanical strength and a 50-mm thick copper shell as corrosion protection are planned to be used for disposal of spent nuclear fuel in Sweden and Finland. Chloride can be considered “beneficial”, as it promotes active dissolution of copper rather than passivation (which might result in pitting), but a high concentration of chloride in solution would increase the driving force for corrosion through the formation of soluble copper chloro complexes. Thermodynamic calculations are performed in this study with the PHREEQC software and three of its accompanying databases, and a comparison with experimental data is performed to select the database to be used when evaluating repository performance. The activity coefficient models are given special attention. For the assessment of chloride-assisted corrosion of a KBS-3 canister, chloride concentrations pessimistically up to 5 mol/kg are used (in Finland and Sweden, the groundwater and bentonite porewater chloride concentrations are not expected to exceed 1 mol/kg). The resulting copper solubilities are then considered in different mass transport cases.     

Effect of atmosphere control on magnetic properties of CaO-Al2O3-SiO2-Fe3O4 glass ceramics

The influences of atmosphere during processes of melting and heat treatment, heat treatment temperature, Fe₃O₄ content and basicity on the magnetic properties of magnetite-based glass ceramics were investigated. For sample containing 20 % Fe₃O₄ melted in different atmospheres, the highest saturation magnetisation was realized in 20vol% air + 80 vol% Ar, due to the fact that ratio of Fe³⁺ to Fe²⁺ in melt obtained in this atmosphere was close to 2. However, it was found that the coercivity of glass ceramics was not affected by the melting atmosphere. A high sintering temperature led to the decrease of saturation magnetisation and the increase of coercivity. As increasing Fe₃O₄ content, the main crystal phase transformed from CaSiO₃ to CaFe_0.6Al_1.3Si_1.08O₆ and finally to magnetite phase, accompanied by the increase of saturation magnetisation and coercivity. In addition, the increase of basicity caused the decrease of saturation magnetisation and the increase of coercivity.     

5A06-O aluminium–magnesium alloy sheet warm hydroforming and optimization of process parameters

The uniaxial tensile test of the 5A06-O aluminium–magnesium (Al–Mg) alloy sheet was performed in the temperature range of 20–300 °C to obtain the true stress–true strain curves at different temperatures and strain rates. The constitutive model of 5A06-O Al–Mg alloy sheet with the temperature range from 150 to 300°C was established. Based on the test results, a unique finite element simulation platform for warm hydroforming of 5A06-O Al–Mg alloy was set up using the general finite element software MSC.Marc to simulate warm hydroforming of classic specimen, and a coupled thermo-mechanical finite element model for warm hydroforming of cylindrical cup was built up. Combined with the experiment, the influence of the temperature field distribution and loading conditions on the sheet formability was studied. The results show that the non-isothermal temperature distribution conditions can significantly improve the forming performance of the material. As the temperature increases, the impact of the punching speed on the forming becomes particularly obvious; the optimal values of the fluid pressure and blank holder force required for forming are reduced.     

天然气水合物储层泥质细粉砂挡砂介质堵塞规律与微观挡砂机制

中国南海海域部分天然气水合物储层中地层砂为高泥质含量细粉砂，开采防控砂难度较大。针对高泥质细粉砂挡砂机制问题，使用粒度中值为10.13 μm的泥质细粉砂样品，模拟单向气液携砂流动条件，使用绕丝筛板、金属烧结网、金属纤维、预充填陶粒4类挡砂介质在20~80 μm挡砂精度下进行挡砂模拟实验，采用显微成像系统观察挡砂介质内部及表面砂粒沉积与堵塞动态，分析介质流通性能和挡砂性能变化，总结堵塞规律、微观挡砂机制与形态及其控制因素。研究结果表明，不同类型和精度的挡砂介质对泥质细粉砂的堵塞总体呈现堵塞开始、堵塞加剧和堵塞平衡3个阶段。随着驱替进行，挡砂介质渗透率逐渐降低，幅度会高达90%以上；同时过砂速度减缓，最终过砂率为5%~10%。根据堵塞规律和微观图像分析，提出了粗组分分选桥架、局部砂团适度挡砂、整体砂桥阻挡等挡砂介质对泥质细粉砂的3种微观挡砂机制。以粗组分分选桥架挡砂机制为主的挡砂工况下，挡砂介质堵塞渗透率较高，但过砂率超过15%，挡砂效果较差；以整体砂桥挡砂机制为主时，过砂率在10%以下，挡砂性能较好，但各类挡砂介质的堵塞渗透率不足1 D，流通性能较差。局部砂团适度挡砂机制为主时介质挡砂性能及流通性能介于两者之间。挡砂介质对天然气水合物储层泥质细粉砂的微观挡砂机制和形态受挡砂介质类型、精度、地层砂特征以及流动条件等因素控制，其规律对于水合物泥质细粉砂防控砂优化有指导意义。     

磨矿动力学研究现状及应用

磨矿动力学是描述被磨物料的磨碎速率与磨矿时间之间关系规律的一种数学模型，对分析物料在磨矿过程中的粒级及能量变化具有重要作用。为充分发挥磨矿动力学在磨矿过程中的作用，论文在分析国内外研究现状的基础上，系统介绍了两种典型的磨矿动力学模型：m阶磨矿动力学模型和磨矿总体平衡动力学模型，分析了模型中各参数的含义；以磨矿总体平衡动力学模型为重点，分析了破碎速率函数和破碎分布函数的求解方式，包括零阶产出率法、奥-勒理论简算法、卡普尔G-H算法以及经验公式法等；从物料性质、磨矿介质及配比、磨矿方式及参数、化学添加剂等几个方面分析了影响磨矿动力学模型的因素；指出了磨矿动力学模型在矿物加工工程领域的应用现状并对其未来的研究方向提出展望。研究表明磨矿动力学在矿物加工领域具有广泛而重要的应用，为进一步改善磨矿工艺提供了理论依据。     

基于面元素重排的三维网格模型数据隐藏算法

目的 为了解决目前三维数据隐藏算法不能兼顾无失真和盲提取的问题，提出一种新的完全无失真的三维网格模型数据隐藏盲算法。方法 首先使用混沌逻辑映射选择嵌入与提取模式，保证数据的安全性。然后利用面元素重排，完全不会造成三维模型失真的性质，通过不同嵌入模式规则对三角面元素进行重排，以嵌入秘密数据。接收端则可根据相应的提取模式规则提取秘密数据。结果 仿真结果与分析表明，该算法不会对三维模型造成任何失真，嵌入容量为每顶点2比特，且能抵抗仿射变换攻击、噪声攻击和平滑攻击等。结论 这种三维数据隐藏盲算法无失真，容量大、安全性高、鲁棒性强，适用于三维载体不容修改的情形，如军事、医学、秘密通信和版权保护等。